Jump to content



Featured Articles

Check out the latest featured articles.

File Library

Check out the latest downloads available in the File Library.

New Article

Product Viscosity vs. Shear

Featured File

Vertical Tank Selection

New Blog Entry

Low Flow in Pipes- posted in Ankur's blog

0

How To Calculated Pump For Wet Scrubber

design pump wet scrubber

6 replies to this topic
Share this topic:
| More

#1 thuyetle

thuyetle

    Brand New Member

  • Members
  • 5 posts

Posted 29 September 2020 - 02:44 AM

How to design Pump for wet scrubber with I have data:

 

Specification of Wet Scrubber

 

Diameter: D1200 mm

Height : 4200 mm

 

How to design Pump, sizing pipe have people help to me design.

 

Thanks you.



#2 breizh

breizh

    Gold Member

  • Admin
  • 6,332 posts

Posted 29 September 2020 - 03:15 AM

hi ,

Difficult to understand your query ! 

What is the gas flowrate to treat , what is the liquid to wash the gas , what are  the specification ( inlet and outlet gas concentration of impurity to treat ) , what is the specification of the liquid ( pure liquid or contaminated liquid) ?

With the design of the column ( height /diameter/ packing height )  I guess you know the flowrates and performance of the scrubber then you have to specify the pump based on the sump ( small storage ) at the inlet and the height to bring the liquid at the top of the column + head losses. 

Minimum height of liquid is required  to prevent cavitation ( NPSHa).

 

 

Consider the documents attached to support your work .

 

You need to supply more information to get a meaningful answer

Probably you need support from knowledgeable people within your organization .

Good luck 

 

Breizh 

 

 

 


Edited by breizh, 29 September 2020 - 03:23 AM.


#3 thuyetle

thuyetle

    Brand New Member

  • Members
  • 5 posts

Posted 29 September 2020 - 04:59 AM

Hi Sir,
 
I am student but I am researching Wet Scrubber If you have document please send me. Thank
I know bit English so I can not explain to some problem is clearly.
I have attached on forum  and I take note on that.
This link : image 
You can explain why have specification but : Sizing pipe, Pump, can't you.
How to calculated pump and sizing pump ? I know you soft of an expert .
Thank you very much

Edited by thuyetle, 29 September 2020 - 05:03 AM.


#4 breizh

breizh

    Gold Member

  • Admin
  • 6,332 posts

Posted 29 September 2020 - 05:41 AM

hi,

take a look at the doc attached .

note : I cannot open your document  ( message error).

Breizh 


Edited by breizh, 29 September 2020 - 05:42 AM.


#5 thuyetle

thuyetle

    Brand New Member

  • Members
  • 5 posts

Posted 30 September 2020 - 02:35 AM

Hi Sr,

 

I attached again and I think  you''ll be open it's "ok"

If you received attached I hope you will support me that I can understand it. 

Lee,

Thank you!

Attached Files


Edited by thuyetle, 30 September 2020 - 02:56 AM.


#6 breizh

breizh

    Gold Member

  • Admin
  • 6,332 posts

Posted 30 September 2020 - 03:48 AM

Hi , 

Thanks for sharing your table .The only good info supplied are the gas flowrate and the power of the pump . I understand  inlet and outlet sizes are related to the gas streams , nothing for the liquid . 

My personal experience with many wet scrubbers installed  in Asia : the pump must be included in the scope of the vendor of scrubbers.

At least he should supply the necessary information to purchase the pump ( TDH vs Qv , Operating flow rate ) .

 

I cannot offer more .

Breizh


Edited by breizh, 01 October 2020 - 12:23 AM.


#7 thuyetle

thuyetle

    Brand New Member

  • Members
  • 5 posts

Posted 30 September 2020 - 09:46 PM

hi sir,

 

thank you support me .






Similar Topics