Jump to content



Featured Articles

Check out the latest featured articles.

File Library

Check out the latest downloads available in the File Library.

New Article

Product Viscosity vs. Shear

Featured File

Vertical Tank Selection

New Blog Entry

Low Flow in Pipes- posted in Ankur's blog

0

Heat Exchanger

heat duty temperature sizing heat exchanger u-tube

6 replies to this topic
Share this topic:
| More

#1 navneet2109

navneet2109

    Veteran Member

  • Members
  • 35 posts

Posted 13 November 2018 - 12:36 AM

 
Dear all Engineers,
 
Please refer attached file while reading this.
 
as per "DESIGN-1" the sizing of shell & tube heat exchanger has been done. In this design the output of propylene temperature is 40c.
 
now the client need the propylene at 45c with the same sized heat exchanger.
So as per "DESIGN-2" we can achieve this by changing the input temp of glycol from 50 to 60 C.
 
In "DESIGN-2" we changed the glycol solution input so the temerature difference become 20C in exchanger 1 (DESIGN-2). 
Previously it was 10C (DESIGN-1).
 
By consulting others regarding this sizing they are not considering 20c difference in exchanger1. so according to consultant we have to change the STHE sizing.
 
My question here are following:
 
1. Is there any problem to have 20c difference of glycol solution in exchager1 (40C input and 60 output)? 
 
2. Is there any criteria for considering temperature difference for STHE?
 
3. Because of this difference the heat duty is increased but the size remains same. So is there anything affecting if the heat duty increased on same sized heat exchanger?
 
Hope you all understand my concern regarding HE sizing. Any other advice relating to Heat Exchanger you are most welcome.
 
Attached File  Untitled.png   37.72KB   1 downloads


#2 Bobby Strain

Bobby Strain

    Gold Member

  • Members
  • 3,528 posts

Posted 13 November 2018 - 07:37 PM

You should rate the exchanger with a proper software.



#3 navneet2109

navneet2109

    Veteran Member

  • Members
  • 35 posts

Posted 13 November 2018 - 11:25 PM

You should rate the exchanger with a proper software.

The screenshot i have attached is from HTRI and from both option i am getting the acceptable design. I think this is the best software for heat exchanger.

Please go through my question again. what i am asking is basically a doubt which i can get from experience personal only.



#4 Pilesar

Pilesar

    Gold Member

  • Members
  • 1,347 posts

Posted 14 November 2018 - 03:24 PM

Experience is something you do not get until just after you need it. You should rate the exchanger with a proper software. Did you use the appropriate inputs? Did you interpret the results correctly? We have no way of knowing.

  It is nice when you can get someone to check your work, but when that is not feasible, you just have to make sure you can defend your conclusion, then call the shot and take the consequences. It is certainly possible that the exchanger is good for the new conditions. If I were reviewing your work, the following checks come to mind:

- Is there any phase change for the fluid?

- Is the heat exchange in the film boiling region?

- Are the velocities acceptable?

- Will the pressure drop work in the hydraulic system?

- Is tube vibration a problem?

- Is the differential thermal expansion accounted for in a fixed tubesheet design?

- Is the pressure relief properly designed?



#5 navneet2109

navneet2109

    Veteran Member

  • Members
  • 35 posts

Posted 15 November 2018 - 03:20 AM

Experience is something you do not get until just after you need it. You should rate the exchanger with a proper software.

I know that i will not get experience when i need it but can't i ask the experience personal if i have any doubt?. I have already mention i used HTRI software.

 

Did you use the appropriate inputs? Did you interpret the results correctly? We have no way of knowing.

Yes i used all the inputs correctly for the "DESIGN-1" (attached screenshot). I am getting the result from both way (DESGN-1 AND DESIGN-2). I can't attached the whole calculation. It will be illegal i think.

  It is nice when you can get someone to check your work, but when that is not feasible, you just have to make sure you can defend your conclusion, then call the shot and take the consequences. It is certainly possible that the exchanger is good for the new conditions. If I were reviewing your work, the following checks come to mind:

- Is there any phase change for the fluid?

please the attached. from that it can be find out that phase change is taking place or not.

 

- Is the heat exchange in the film boiling region?

no boiling

- Are the velocities acceptable?

yes velocity is acceptable

 

- Will the pressure drop work in the hydraulic system?

for the "DESIGN-2" tube side pressure drop allowed is 0.7kg.cm2 and i am getting 0.68kg/cm2. Is it acceptable or not.

 

- Is tube vibration a problem?

​i am using impingement plate.

 

- Is the differential thermal expansion accounted for in a fixed tubesheet design?

its u-tube. for tubesheet we have considered for the expansion.

 

- Is the pressure relief properly designed?

not required for heat exchanger vessel.


Edited by navneet2109, 15 November 2018 - 03:22 AM.


#6 Chemitofreak

Chemitofreak

    Gold Member

  • Members
  • 291 posts

Posted 16 November 2018 - 09:29 AM

Here are my two cents:

 

1) There are various glycols available, we don't know which one you are using. Maybe you should search some literature with respect to the glycol you are using, this will help you to check whether the glycol is o.k at 60 degC or it can undergo thermal degradation. 

 

2) Temperature difference across the Heat Ex is solely governed by the process.

 

3) The Client wants you to increase the outlet temperature of one fluid, by keeping the area constant. That can be done by one of the way you have already tried.



#7 navneet2109

navneet2109

    Veteran Member

  • Members
  • 35 posts

Posted 16 November 2018 - 10:56 AM

Here are my two cents:

Your two cents are more valuable.

 

1) There are various glycols available, we don't know which one you are using. Maybe you should search some literature with respect to the glycol you are using, this will help you to check whether the glycol is o.k at 60 degC or it can undergo thermal degradation. 

​I will definitely check glycol properties for 60degC.  

 

2) Temperature difference across the Heat Ex is solely governed by the process.

You are correct.

 

3) The Client wants you to increase the outlet temperature of one fluid, by keeping the area constant. That can be done by one of the way you have already tried.

By this sentence I have gain little bit confidence that it can be done. My main concern was only that we can go of 20 degC difference. 

 

I am very grateful to you for answering after understanding the points.

regards


Edited by navneet2109, 16 November 2018 - 10:58 AM.





Similar Topics