Jump to content



Featured Articles

Check out the latest featured articles.

File Library

Check out the latest downloads available in the File Library.

New Article

Product Viscosity vs. Shear

Featured File

Vertical Tank Selection

New Blog Entry

Low Flow in Pipes- posted in Ankur's blog

1

Activated Carbon Selection


2 replies to this topic
Share this topic:
| More

#1 Talhafarooq

Talhafarooq

    Brand New Member

  • Members
  • 1 posts

Posted 25 November 2024 - 12:20 AM

Greetings All,
 
We want to know about the working tendency of our activated carbon filter on amine sweetening unit in lean amine circuit.
 
As part of a recent process adjustment, we  increase the flow rate from 25 m³/hr to 30 m³/hr to meet current operational requirements. In this case, we would like to inquire about several key specifications or charts related to the granular size of the activated carbon, including:
  • Recommended GPM/ft² values
  • Bed volume, length and diameter
  • Pressure drop considerations when passing lean amine
 
Another option we considering the replacement of a carbon filter with cartridge filters, it is essential to carefully evaluate the selection criteria and determine the appropriate number of cartridges, along with key operational parameters 
 
  • Recommended GPM/ft² values
  • filter volume, length and diameter
  • Pressure drop considerations when passing lean amine
I am looking forward to your response.
 
Regards,


#2 breizh

breizh

    Gold Member

  • Admin
  • 7,062 posts

Posted 25 November 2024 - 12:42 AM

Hi,

Attached documents to support your work.

Note: probably good to ring your supplier for advises.

Edit: make sure you can dispose easily this material, very difficult in some countries.

Breizh

Attached Files



#3 AsherMuse

AsherMuse

    Brand New Member

  • Members
  • 6 posts

Posted 19 November 2026 - 01:53 AM

Good question, and the increase from 25 to 30 m3/h is exactly the point at which a carbon bed should be re-checked from its duty, rather than simply re-rated on flow alone. A single catalogue GPM/ft2 figure is not enough on its own.

1. Start from the duty, not from a flux number

Before sizing anything, fix the duty: lean amine at 30 m3/h (about 132 US gpm), amine concentration, temperature and viscosity, and above all what the carbon has to remove - dissolved hydrocarbons, amine degradation products, surfactants and foaming precursors, plus FeS and other corrosion solids. Dissolved contaminants are what make this a carbon bed; solids alone are a filtration duty. Ask the carbon vendor for the flux and the empty-bed contact time for your carbon grade at that duty, then check the arithmetic yourself: bed area = flow / flux, and bed volume = flow x empty-bed contact time, with bed depth normally in the region of 0.8 to 1.2 m and diameter taken from volume / depth. If the vendor's flux gives a bed much smaller than that, ask what contact time and what contaminant load it was based on.

2. Differential pressure - size on the fouled bed, not the clean bed

Agree a clean-bed differential pressure and a change-out differential pressure with the vendor, fit a differential pressure gauge across the bed, and log it. Going from 25 to 30 m3/h raises velocity by 20%, and differential pressure rises with velocity, faster still if fines or hydrocarbon coating cause channelling. Do not judge the bed on differential pressure alone: a bed can show a normal differential pressure and still be exhausted for adsorption, so also watch amine quality - foaming tendency, colour, hydrocarbon carryover and what the downstream filter is catching.

3. Cleaning and change-out

In lean amine service carbon is normally replaced rather than backwashed in place, so design the change-out in from the start: isolation, drain and vent, manway access, a proper support grid, and a disposal route for the spent carbon. Do not steam or air-blow a loaded bed without a procedure agreed with the vendor.

4. Retain the carbon properly - specify the mesh as a system

Support the bed on a perforated support cylinder or grid behind a fine mesh, and specify that mesh as a complete system, not by aperture alone - grade, aperture with tolerance, wire diameter and minimum open area together, for example 316L plain weave, 2.0 mm aperture +/-0.2 mm, 0.5-0.7 mm wire, minimum 56% open area. The mesh must be finer than the smallest carbon particle so carbon cannot pass, while the open area is high enough to keep its own differential pressure low.

5. Replacing carbon with cartridges is a change of duty

Cartridge filters remove solids; they do not adsorb dissolved hydrocarbons, degradation products or surfactants. Replace the carbon bed with cartridges only if analysis shows the problem is particulate. If adsorption is still needed, keep the carbon and use cartridges as polishing downstream. Protect fine cartridges with a 500-2000 micron pre-filter upstream, so that FeS fines and solids slugs do not blind them in one event, and size the cartridges from the vendor's flux per element at your temperature and viscosity, with a change-out differential pressure per the element data.

6. Materials

316L is the normal wetted material for lean amine here. Move to duplex 2205 only if a chloride / stress corrosion cracking threat is demonstrated by analysis. If it is, demand PMI, ferrite balance and WPS/PQR records for the duplex fabrication.

If you can share the amine concentration, temperature, a contaminant and solids analysis, the carbon grade, the existing vessel dimensions and the clean-bed differential pressure, the vendor sizing can be checked properly instead of guessed.




Similar Topics